Page 1 of 1

Beringer DSP9024

PostPosted: Thu Dec 02, 2004 6:43 pm
by ke1gf
Hello, I just picked up a 9024 and I'm having a problem trying to turn off the noise gate I can select values between -96 and -25 but I can't make the value go to "OFF" any help would be appreciated... Blaine! HELP!

-Bill 'GF

PostPosted: Thu Dec 02, 2004 9:48 pm
by blaine
set all the bands gate to -96 and bring up your input gain so you have more drive, it shouldnt trigger after that.

PostPosted: Fri Dec 03, 2004 10:20 am
by ke1gf
strage Blane, in the book it states that you can set the gate to "OFF" I guess you can't. Thanks though.

-Bill 'GF

PostPosted: Fri Dec 03, 2004 10:48 pm
by ke1gf
Blane also I need some suggestions as to how I should have the 6 bands dispersed what frequency ranges are you using for each band if you don't mind me asking? I would like to have the 6th band's top frequency set a 5kc so... Kinda like a brick wall so I'm not too wide.

-Bill

PostPosted: Sat Dec 04, 2004 9:27 pm
by blaine
Here are the settings for my 9024, of course feel free to change for your voice, twiddle with the freqs or cut boost each out gain.
you may need to back down the input to your class E rig a bit too.
I went from 12 to 10 o'clock on the input knob to my rig ( you could also drop the outgain of each channel, but then the meters on the display dont bounce enough for me :P )

NO tube emulation
NO Ultramizer
NO exciter
48Khz sample rate
DELAY 20ms

ingain +5db bandlink OFF
peak limiter -2
lim release .50 sec

BAND 1
OUTGAIN +0
LO FREQ 40
HI FREQ 150
GATE THR -90
COMP THR -25 DB
COMP RATIO INF
COMP ATT 0ms
COMP REL 450ms
COMP KNEE hard

BAND 2
OUTGAIN -1
LO FREQ 150
HI FREQ 500
GATE THR -90
COMP THR -25 DB
COMP RATIO INF
COMP ATT 0ms
COMP REL 400ms
COMP KNEE hard

BAND 3
OUTGAIN -1
LO FREQ 500
HI FREQ 1K
GATE THR -90
COMP THR -25 DB
COMP RATIO INF
COMP ATT 0ms
COMP REL 450ms
COMP KNEE hard

BAND 4
OUTGAIN +0
LO FREQ 1K
HI FREQ 2.5K
GATE THR -90
COMP THR -25 DB
COMP RATIO INF
COMP ATT 0ms
COMP REL 450ms
COMP KNEE hard

BAND 5
OUTGAIN +1
LO FREQ 2.5K
HI FREQ 7K
GATE THR -90
COMP THR -25 DB
COMP RATIO INF
COMP ATT 0ms
COMP REL 350ms
COMP KNEE hard

BAND 6
OUTGAIN +1
LO FREQ 7K
HI FREQ 9K
GATE THR -90
COMP THR -25 DB
COMP RATIO INF
COMP ATT 0ms
COMP REL 350ms
COMP KNEE hard

PostPosted: Sun Dec 05, 2004 7:28 am
by ke1gf
Thanks Blane.

-Bill

AOK into the Blackstone valley.

PostPosted: Sun Dec 05, 2004 8:43 am
by N9NEO
Bill,

Got a FB sig into Uxbridge - Gateway to the Blackstone Valley.

Heard you on when I was supposed to be studying :D Was on the SP600 into a Marantz, into a pair of AR speakers.

Have to tell you you're audio was on a par with Blaine or Steve. I think you got the recipe goin on. A smokin good signal over here.

Probably going to have to ditch school next semester. Between the 9-5 thing, kids, and school there was no time left for radio. You guys are having way way too much fun without me.

73
Bob

PostPosted: Sun Dec 05, 2004 12:51 pm
by blaine
i wanna hear it, did you get it setup yet?

maybe yesterday????

PostPosted: Sun Dec 05, 2004 3:27 pm
by N9NEO
I think it was late morning or early afternoon yesterday that I heard you. So whatever you were running... But then again you're audio is usually FB into here. Most of the time I run the 3kHz wide HQ170, so maybe the SP600 setup at this end.. heheh.

73
Bob

PostPosted: Sun Dec 05, 2004 8:47 pm
by ke1gf
Yup Blaine, I got it I think on this past Thursday, played with it for a few days... Put it on the air sometime early saturday morning, KG2IR said I was running too much compression (3:1) suggested to me that I turn it down to 2:1 but I didn't cause I'm a stubborn bastard. Been out all day, I just finally got home.

-Bill

PostPosted: Sun Dec 05, 2004 9:25 pm
by ke1gf
Hrmn Well Here's how I have the six bands divided up
1: 20 -> 120Hz
2: 120 -> 200Hz
3: 200 -> 630Hz
4: 630 -> 1.5125kHz
5: 1.5125 -> 3.5750kHz
6: 3.5750kHz -> 6kHz

Anyway, I'm just learning so I'm sure the'll be changed around.

-Bill