Single ended. New Project

Welcome and feel free to ask questions about class E, mosfet's, and AM.
You must be registered to post.

Single ended. New Project

Postby yb0djh » Sun Dec 11, 2011 2:11 am

Hi


This is my new project, a single ended Class E. This version i try to use digital driver.

Mechanical Works .. hmm
Image


VFO, divider and driver already done. Unfortunately i was wrong order of Mosfet driver, should be TO-220 package, but by mistake i ordered PI type (DIL). Please advise where i can get IXDD414 CI (TO-220)

Will inform you the progresses..

BR, Agus- yb0djh
Image
yb0djh
Member
 
Posts: 18
Joined: Sun Apr 03, 2005 7:57 am
Location: Indonesia Jakarta

Re: Single ended. New Project

Postby Gilly » Mon Dec 12, 2011 5:44 pm

Hi Agus


Steve should have plenty of the IXDD414....
If you order some through him get a few 11N90 FETs as well.....I would not use the IRFP450/460 ....

The TC4422 are quite good too and are available via the WEB...
They are rated at 9 Amps while the IXDD414 are 14 Amps..

Looks as though the TX is for 40M...is that right... :?:


Wayne
VK3ALK
Gilly
Class E Enthusiast
 
Posts: 167
Joined: Tue May 15, 2007 6:59 pm
Location: Mt.Eliza Victoria Australia

Re: Single ended. New Project

Postby kf1z » Tue Dec 13, 2011 9:42 am

I have a few still as well....

Check in the "Parts and Sources" section of the forum..

Bruce
kf1z
User avatar
kf1z
Senior Contributer
 
Posts: 558
Joined: Sat Mar 18, 2006 7:07 am
Location: Ely, NV.

Re: Single ended. New Project

Postby yb0djh » Wed Dec 14, 2011 12:34 am

Gilly wrote:Hi Agus Looks as though the TX is for 40M...is that right... :?:



80 Mtr actually, my targets are: 100 watt, 80 M, 42 VDD, Q=10, CMOS driver. Simple mission: Just try to reinventing the wheel :) to get the grip of class E.


73s Agus - YB0DJH
Image
yb0djh
Member
 
Posts: 18
Joined: Sun Apr 03, 2005 7:57 am
Location: Indonesia Jakarta

Re: Single ended. New Project

Postby Diego-CX4DI » Thu Dec 15, 2011 8:18 am

Hi dear,

IXDD414(T220) is not available at the present.

we got in digikey the MIC-4451ZT and MIC-4452ZT(TO-220) 12A working good in 7Mhz, direct coupling throungh a 0.1 ohms SMD resistor(digikey HPC12JTR100CT-ND).

kind regards,
Diego
CX4DI
cx4di@adinet.com.uy
Class E with PWM modulation
Diego-CX4DI
Member
 
Posts: 43
Joined: Fri Sep 30, 2005 10:22 am
Location: Montevideo-Uruguay

Re: Single ended. New Project

Postby yb0djh » Sun Dec 25, 2011 10:52 am

Dear All


Wish everyone a joyous Christmas season.

Below picture is the results of Single ended Class E, with very ugly type of soldering :D .

1. Oscilator Vackar operate 7 - 8 mhz
2. Cmos Divider and phase shifter
3. Mosfet driver IXDD414 (DIL)
4. Duty cycle can be trimmed

I dont have a accurate Power Meter, so i cannot calculate the efficiency, but it seems Mosfet temperature was touchable running 43 volt 3 amp.

Image

And here is the Class E waveform

Image

73s Agus-YB0DJH
Image
yb0djh
Member
 
Posts: 18
Joined: Sun Apr 03, 2005 7:57 am
Location: Indonesia Jakarta

Re: Single ended. New Project

Postby Gilly » Sun Dec 25, 2011 7:12 pm

Hi Agus

All looks good there.....

Is this going to be a permanent TX ?

Also for Power Meters I use this method most of the time and is cheap to build....
You could use your CRO etc:

http://www.k4eaa.com/dummy.html

How is your PWM going :?:


Wayne
Gilly
Class E Enthusiast
 
Posts: 167
Joined: Tue May 15, 2007 6:59 pm
Location: Mt.Eliza Victoria Australia

Re: Single ended. New Project

Postby yb0djh » Wed Dec 28, 2011 11:30 pm

Hi Wayne


Thank you, i m busy to crank up the efficiency. The first try was 45% efficiency, after trimming here and there i can get 70% and STOP :oops: can not go higher. I suspect the coil because it was hot when transmit (but still touchable). The VCE and Class e Waveform it looked perfect.

I don't think i will as permanent transmitter, maybe for demo. see, the yellow toroid is VFO in open, i will wash up the band when i use it :D

Thank you for power meter link, i will install diode in my MFJ dummy load.

PWM at this moment i keep it as it was, i m focus on experimenting on RF deck.

BR. Agus-YB0DJH
Image
yb0djh
Member
 
Posts: 18
Joined: Sun Apr 03, 2005 7:57 am
Location: Indonesia Jakarta

Re: Single ended. New Project

Postby Diego-CX4DI » Mon Jan 09, 2012 9:22 am

what is the power mosfet are you using?

73's
Diego
CX4DI
cx4di@adinet.com.uy
Class E with PWM modulation
Diego-CX4DI
Member
 
Posts: 43
Joined: Fri Sep 30, 2005 10:22 am
Location: Montevideo-Uruguay


Return to Class E Discussion

Who is online

Users browsing this forum: Bing [Bot] and 1 guest

cron